- 您现在的位置：买卖IC网 > Sheet目录307 > ADE7758ARWZRL (Analog Devices Inc)IC ENERGY METERING 3PHASE 24SOIC
ADE7758
(see the Active Power Calculation section). Equation 14 gives an
Data Sheet
expression for the instantaneous power signal. This is filtered by
LPF2, which has a magnitude response given by Equation 23.
E(t)
Vlt
H ( f ) =
1
1 + f
2
8 2
(23)
? × cos ( 4 π f 1 t )
? VRMS × IRMS ?
( 2 f 1 ) 2 2 ?
1 +
2f 1 2 × cos(4 π × f 1 × t)
4 π × f 1 1 +
The active power signal (output of the LPF2) can be rewritten as
? ?
p ( t ) = VRMS × IRMS ? ? (24)
?
? ?
? 8 ?
where f 1 is the line frequency, for example, 60 Hz.
From Equation 24, E(t) equals
VI
–
8
t
Figure 70. Output Frequency Ripple
Line Cycle Active Energy Accumulation Mode
The ADE7758 is designed with a special energy accumulation
VRMS × IRMS
VRMS × IRMS × t – ?
? 4 π f 1 1 + ( 2 f 1 )
? × cos( 4 π f t ) (25)
?
?
?
? 2
?
? 8 2
?
?
?
? ?
1
mode that simplifies the calibration process. By using the on-
chip, zero-crossing detection, the ADE7758 updates the watt-hr
accumulation registers after an integer number of zero crossings
(see Figure 71). The line-active energy accumulation mode for
watt-hr accumulation is activated by setting the LWATT bit
From Equation 25, it can be seen that there is a small ripple in
the energy calculation due to the sin(2ωt) component (see
Figure 70). The ripple gets larger with larger loads. Choosing a
lower output frequency for APCF during calibration by using a
large APCFDEN value and keeping APCFNUM relatively small
can significantly reduce the ripple. Averaging the output
frequency over a longer period achieves the same results.
(Bit 0) of the LCYCMODE register. The total energy accumu-
lated over an integer number of half-line cycles is written to the
watt-hr accumulation registers after the LINECYC number of zero
crossings is detected. When using the line cycle accumulation
mode, the RSTREAD bit (Bit 6) of the LCYCMODE register
should be set to Logic 0.
WATTOS[11:0]
WG[11:0]
WDIV[7:0]
ACTIVE POWER
+
+
%
+
+
40
0
ZXSEL0 1
ZERO-CROSSING
DETECTION
(PHASE A)
ZXSEL1 1
15
WATTHR[15:0]
0
ACCUMULATE ACTIVE POWER FOR
LINECYC NUMBER OF ZERO-CROSSINGS;
WATT-HR ACCUMULATION REGISTERS
ARE UPDATED ONCE EVERY LINECYC
NUMBER OF ZERO-CROSSINGS
ZERO-CROSSING
DETECTION
(PHASE B)
ZXSEL2 1
ZERO-CROSSING
DETECTION
(PHASE C)
CALIBRATION
CONTROL
LINECYC[15:0]
1 ZXSEL[0:2] ARE
BITS 3 TO 5 IN THE LCYCMODE REGISTER
Figure 71. ADE7758 Line Cycle Active Energy Accumulation Mode
Rev. E | Page 34 of 72
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ADE7761AARSZ-RL
IC ENERGY METERING 1PHASE 20SSOP
ADE7761BARSZ-RL
IC ENERGY METERING 1PHASE 20SSOP
ADE7768ARZ-RL
IC ENERGY METERING 1PHASE 16SOIC
ADE7769ARZ-RL
IC ENERGY METERING 1PHASE 16SOIC
ADM8843ACPZ-REEL7
IC LED DRVR WHITE BCKLGT 16LFCSP
ADP1653ACPZ-R7
IC LED DRVR PHOTO FLASH 16-LFCSP
ADP1712-EVALZ
BOARD EVALUATION ADP1712
ADP1720-EVALZ
BOARD EVAL FOR ADP1720-ADJ
相关代理商/技术参数
ADE7759
制造商:AD 制造商全称:Analog Devices 功能描述:Active Energy Metering IC with di/dt Sensor Interface
ADE7759ARS
功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSRL
功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZ
功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZRL
功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7760
制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection
ADE7760ARS
制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube
ADE7760ARSRL
制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP T/R 制造商:Analog Devices 功能描述:ENERGY METER IC W/ONCHIP FAULT & OSCIL. - Tape and Reel